BTSC JE · Module 42 · standard depth · 17 min
Compaction of soils: Proctor tests, OMC and MDD, and field control
What BTSC JE asks from this chapter
Syllabus lines this chapter covers:
- CBT: Civil technical (diploma level) · Building materials, concrete technology, estimating and costing
- CBT: Civil technical (diploma level) · Surveying, soil mechanics, hydraulics and irrigation
- CBT: Civil technical (diploma level) · Transportation, environmental engineering
- CBT: Civil technical (diploma level) · Theory of structures, RCC design, steel design
BTSC JE questions from this module are being sorted into our bank.
Cut to standard depth for BTSC JE. 3 deeper paragraphs are in the full chapter.
Start from zero: why we press soil
Watch a village path being made before the rains. People spread soil, sprinkle a little water and beat it with a heavy wooden tamper. A loose heap that sank under every footstep becomes a hard track that carries carts.
The same idea runs every highway, railway bank and earth dam. Loose soil has many air-filled gaps between its grains. When we press it with a roller or a rammer, the grains slide closer and the air is pushed out, so each cubic metre holds more solid soil. This process is compaction.
Two things are worth noticing in the village example. First, nothing was added or removed except air: the grains and the water stayed the same. Second, the people added a little water, not a lot, because they knew from experience that bone-dry soil and muddy soil both refuse to pack well.
This chapter explains that experience in numbers. We see why there is a best water content, how the laboratory finds it, how the result changes with the effort applied, and how a site engineer checks that the field work matches the laboratory target.
Why it matters. Compaction is the cheapest ground improvement there is. A well-compacted embankment is stronger, settles less and lets less water through. Poorly compacted fill is behind many cracked roads, sunken culvert approaches and leaking canal banks.
What compaction does, and what it is not
Compaction applies mechanical energy, such as rolling, ramming or vibrating, to rearrange the soil grains and reduce the void ratio. Usually the water content does not change during compaction, and the grains themselves are not broken. Only air leaves the soil.
The engineer compacts soil for three reasons:
- Compaction raises the shear strength, so slopes stand steeper and foundations carry more load.
- Compaction reduces settlement, because the grains have already been pushed close together.
- Compaction reduces permeability, so less water seeps through an embankment or a canal bank.
Compaction is used for embankments, road bases, runways, earth dams and reinforced-earth walls, and also to level ground before building. It is the first improvement tried on any fill, because it needs only machines that a contractor already has.
Why it matters. If you confuse the two, you pick the wrong remedy. A soft saturated clay under a new embankment will not improve by rolling it harder, because the water cannot escape quickly. It needs time, drainage or preloading, which consolidation explains.
The laboratory compaction tests
Before rolling starts on site, the laboratory finds how dense the soil can get and at what water content. The Indian Standard gives two tests, which match the older Standard and Modified Proctor tests.
In the light compaction test, about 3 kg of air-dried soil passing the 4.75 mm sieve is mixed with water. It is compacted into a 1000 cm³ mould in 3 equal layers, each layer receiving 25 blows of a 2.6 kg rammer falling freely through 310 mm. The mould is weighed, a moisture sample is taken, and the test is repeated with about 2% more water each time, until the mass of compacted soil first rises to a peak and then falls.
The heavy compaction test was developed because the light test could not reproduce the higher densities that modern heavy rollers achieve. It uses the same mould and 25 blows per layer, but 5 layers, a 4.9 kg rammer and a 450 mm drop.
We can compare the energy of the two tests per unit volume. The light test gives 2.6 × 9.81 × 0.31 × 25 × 3 ÷ 0.001 ≈ 593 kJ/m³, and the heavy test gives 4.9 × 9.81 × 0.45 × 25 × 5 ÷ 0.001 ≈ 2,700 kJ/m³. So the heavy test applies roughly 4.5 times more energy.
From each trial, the dry density is worked out from the bulk density and the water content, using γd = γ/(1 + w). Plotting dry density against water content gives the compaction curve.
Why it matters. The test chosen must match the field work. Light compaction suits small works and light equipment, while heavy compaction is used for highways, airfields and railway formations where heavy rollers are used. A specification that says "95% MDD" means nothing until it says which test.
The compaction curve: OMC and MDD
For soils with fines, the compaction curve rises, reaches a peak and falls, like an upside-down V. The water content at the peak is the optimum moisture content (OMC), and the dry density there is the maximum dry density (MDD).
Why does the curve have a peak? At low water content, the grains are dry and rough, and friction stops them sliding past each other. Adding water forms thin films around the grains that act like a lubricant, so the same blows push them closer and the dry density rises.
Beyond the optimum, the extra water starts to fill space that grains could have occupied. Water cannot be squeezed out quickly by blows, so the dry density falls. In short, water first helps packing as a lubricant and then hinders it by taking up room.
Two reference lines are drawn on the same graph. The zero-air-voids line, γd = Gγw/(1 + wG), shows the dry density if all air were removed, and lines for 5% or 10% air voids lie just below it. The compaction curve always stays to the left of the zero-air-voids line, because no compaction can push out every bubble of air.
The curve also changes with effort. A greater effort raises the MDD and lowers the OMC, so the heavy-test curve sits higher and to the left. The gain from extra effort is large on the dry side of optimum and very small on the wet side, where water, not air, fills the voids.
Soil type matters too. Well-graded sands and gravels give high MDD at low OMC, while plastic clays give lower MDD at higher OMC and a flatter curve.
Why it matters. The OMC tells the site engineer how much water to add before rolling, and the MDD sets the density target. Rolling a soil far wet of optimum wastes fuel, because extra passes cannot squeeze out the water.
Dry side or wet side: same density, different soil
Two samples of the same clay can have the same dry density, one compacted a little dry of optimum and one a little wet of it. Surprisingly, they behave quite differently, because their grains are arranged differently.
On the dry side, the water films around clay plates are thin. The plates meet edge to face in a random, card-house pattern called a flocculated structure. On the wet side, the thicker water films let the plates slide into a more parallel arrangement, called a dispersed structure.
These two structures lead to different behaviour:
| Property | Dry of optimum | Wet of optimum |
|---|---|---|
| Swelling on wetting | More swelling, because the soil is short of water | Less swelling |
| Shrinkage on drying | Less shrinkage | More shrinkage, because parallel plates pack closer |
| Compressibility at low stress | Lower, because the random frame acts like a truss | Higher |
| Permeability | About the same in all directions | Higher along the plates than across them |
| Pore pressure during construction | Low or even negative | Higher |
| Stress-strain behaviour | Stiff, with a peak, then the frame breaks | More flexible and ductile |
At high stresses, both samples are crushed into a similar structure, and the differences fade away.
Designers use these differences on purpose. The clay core of an earth dam is often placed slightly wet of optimum, because a flexible core can follow small settlements without cracking, and its permeability across the flow is low. A subgrade below a road on swelling soil, on the other hand, may be placed near or slightly wet of optimum to limit later swelling.
Why it matters. The water content written into a specification is a design decision, not a detail. Choosing the side of optimum controls cracking, swelling and leakage for the whole life of a dam or road.
Compacting sands and gravels
Clean sands and gravels behave differently from clays. They have no fines to hold water films, so the compaction curve is flat and often confusing. Such soils can be compacted to high density either quite dry or fully saturated, and a little moisture in between can even resist packing.
For these soils, vibration is by far the most effective method. Vibration shakes the grains loose for a moment, and they settle into a tighter arrangement under their own weight and the load of the machine. Flooding the soil with water can also help, because water seeping through pushes grains into stable positions, but it needs a lot of water.
Because the Proctor test does not suit clean sands, their compaction is specified by relative density, ID = (emax − e)/(emax − emin). A typical requirement for fills that must carry heavy loads or resist earthquakes is a dense state, that is a relative density in the upper bands.
Why it matters. Sand fills behind bridge abutments, below machine foundations and under floor slabs are common in practice. Rolling them with a sheepsfoot roller, which suits clay, achieves little. The right tool is a vibratory roller or plate, used at a sensible layer thickness.
Field compaction and quality control
On site, soil is spread in layers, watered to near the OMC and rolled. The choice of roller depends on the soil:
- A smooth-wheel roller suits granular bases and gives a smooth finished surface.
- A sheepsfoot (tamping-foot) roller has projecting feet that knead clay from the bottom of the layer upward, so it suits cohesive soils.
- A pneumatic-tyred roller kneads with many rubber tyres and works on a wide range of soils, including silty and clayey ones.
- A vibratory roller or plate is the right choice for sands and gravels.
The specification states a relative compaction, also called degree of compaction: the field dry density as a percentage of the laboratory MDD. For example, it may require at least 95% of MDD, with the water content kept within a band around the OMC. Railway formations are stricter, asking for about 98% of the heavy-compaction MDD with moisture within ±2% of the OMC.
To check each layer, the field dry density is measured by the sand replacement or core cutter method. The water content is found quickly with a rapid moisture meter, so a failed layer can be re-rolled before the next one is placed on it.
A worked check. The laboratory heavy-compaction MDD of a soil is 1.85 g/cm³ at an OMC of 14%. A field test on a layer gives a bulk density of 2.02 g/cm³ at a water content of 15%. The field dry density is 2.02/1.15 = 1.757 g/cm³, so the relative compaction is 1.757/1.85 = 95.0%. The layer just meets a 95% requirement, and its moisture is within 1% of the OMC.
Try it yourself. On ujjwalinfra, the Standard Proctor lab plots a compaction curve with the zero-air-voids line. The guided compaction lab with a rapid moisture meter and the sand replacement lab take you through field control from reading the meter to the final pass-or-fail report. The lab CBR test then shows how the strength of a compacted subgrade is measured.
Why it matters. Field control is where specifications turn into real roads. A JE who tests each layer and rejects a wet, under-compacted lift saves the department from repairs that would cost many times more after the first monsoon.
Quick revision
- Compaction removes air by mechanical energy, while consolidation removes water slowly under a steady load.
- Compaction raises strength, lowers settlement and lowers permeability.
- The light test uses 3 layers, a 2.6 kg rammer and a 310 mm drop, while the heavy test uses 5 layers, a 4.9 kg rammer and a 450 mm drop, both with 25 blows per layer in a 1000 cm³ mould.
- The heavy test applies about 4.5 times the energy of the light test.
- Dry density peaks at the OMC, and the peak value is the MDD.
- The compaction curve always lies to the left of the zero-air-voids line γd = Gγw/(1 + wG).
- More compactive effort gives a higher MDD and a lower OMC.
- Dry of optimum gives a flocculated structure that swells more, and wet of optimum gives a dispersed structure that shrinks more.
- Sands are compacted best by vibration and are specified by relative density.
- Field work is controlled by relative compaction, which is field dry density as a percentage of the laboratory MDD.