UPSC IFoS · Module 80 · standard depth · 21 min
Soil formation and the three-phase system: void ratio, water content and unit weights
What UPSC IFoS asks from this chapter
Syllabus lines this chapter covers:
- Main: optional subjects (choose any two, 2 papers each) · Civil Engineering
UPSC IFoS questions from this module are being sorted into our bank.
Cut to standard depth for UPSC IFoS. 3 deeper paragraphs are in the full chapter.
Start from zero: what is inside a handful of soil?
Pick up a handful of damp sand from a riverbank and squeeze it. It holds its shape for a moment, then crumbles. Now pour water on it and it slumps; leave it in the sun and it turns to loose dust.
The sand did not change, but its behaviour changed completely. That happened because a handful of soil is never one material. It is a crowd of tiny solid grains, with water and air filling the gaps between them.
Engineers deal with soil in four ways. We build on it (the foundation of a house or a bridge pier), we build in it (basements, culverts and tunnels), we build with it (road embankments and earth dams), and we hold it back (retaining walls). In every case the question is the same: how much load can it carry, how much will it settle, and how will water move through it?
This chapter lays the base for the whole of soil mechanics. First we see how soils form, then we learn to describe any soil with a few numbers, such as void ratio, water content and unit weight. Every later topic, from compaction to bearing capacity, uses these numbers.
Why it matters. Steel and concrete arrive with known strength from a factory. Soil arrives with whatever nature left there, so the engineer must measure it first. A wrong unit weight puts every earth-pressure and settlement calculation wrong from the very first line.
How soils are born: weathering and transport
All soils come from rock. The earth's crust is made of three rock families: igneous rock from cooled magma, sedimentary rock from cemented layers of sediment, and metamorphic rock that heat and pressure have changed. Over thousands of years, weather breaks these rocks into pieces.
Physical weathering only breaks the rock into smaller pieces, without changing what it is made of. Daily heating and cooling, water freezing in cracks, wind and running water all do this work. Its products are mostly coarse soils such as gravel and sand.
Chemical weathering changes the rock itself. Rainwater reacts with minerals through hydration, oxidation and carbonation, and new minerals form, mainly clay minerals. This happens fastest where it is warm and wet, so humid tropical regions have deep, fine-grained weathered soils.
Once formed, a soil either stays in place or travels. A residual soil stays where it formed, usually 5 to 20 m deep, and it grades slowly into the unweathered rock below. A transported soil has been carried away, and it is named after the agent that carried it:
- Rivers leave alluvial deposits, and lakes leave lacustrine deposits in seasonal layers.
- The sea leaves marine deposits, which often contain shells and organic matter.
- Glaciers leave glacial deposits, which are well graded because ice crushes and grinds every size together.
- Wind leaves aeolian deposits, which are uniformly graded because wind can lift only a narrow range of grain sizes.
India shows all of these at work. The vast northern plains are river alluvium, and the black soils of the Deccan plateau formed from the basalt of the Deccan traps. Black soils swell when they get wet and crack wide when they dry. Laterite forms where high temperature and heavy rain wash out the soluble minerals.
Why it matters. The history of a soil tells you what to expect before you test it. River alluvium can change from sand to clay within a few metres, so one borehole is never enough. An expansive black soil can lift a light building and crack it, which is why its foundations need special design.
The three-phase diagram and the basic ratios
In real soil the grains, water and air are mixed together. To calculate anything, we imagine pulling them apart into three neat layers: solids at the bottom, water in the middle and air on top. This picture is the three-phase diagram, and every formula in this chapter comes from it.
On the left side we write volumes: Vs for solids, Vw for water and Va for air. Water and air together fill the voids, so Vv = Vw + Va and the total volume is V = Vs + Vv. On the right side we write masses: Ms for solids and Mw for water, while the mass of air is taken as zero.
Volumes of water and air keep changing with rain and drying, but the volume of solids stays fixed. So the main volume ratio uses solids as the reference:
- Void ratio e = Vv / Vs. It can be more than 1, and soft clays often have e above 1.
- Porosity n = Vv / V. It is always less than 1, and it links to void ratio as n = e/(1 + e) and e = n/(1 − n).
- Degree of saturation S = Vw / Vv. It is 0% for dry soil and 100% when every void is full of water.
- Air content ac = Va / Vv, and percentage air voids na = Va / V.
Two more numbers describe masses:
- Water content w = Mw / Ms. Notice that the bottom is the mass of solids, not the total mass, so w can exceed 100% in very soft clays and peat.
- Specific gravity of solids G (also written Gs) = density of the solid grains ÷ density of water. For most inorganic soils G lies between 2.60 and 2.80, and organic matter brings it down.
Why it matters. Void ratio tells you how much room the grains have to squeeze together, and that decides settlement. Degree of saturation tells you whether water pressure will build up under load. These two numbers alone already predict a lot about how a soil will behave.
Unit weights: bulk, dry, saturated and submerged
Unit weight is weight per unit volume, measured in kN/m³. Density is mass per unit volume, in kg/m³ or g/cm³, and the two are linked by γ = ρg. Engineers use unit weight because loads and pressures are forces.
The same soil can have four different unit weights, depending on what we count:
- Bulk (moist) unit weight γ = total weight / total volume, as the soil exists in the field.
- Dry unit weight γd = weight of solids / total volume. This is the number used to judge compaction, because it tells you how many solids are packed into each cubic metre.
- Saturated unit weight γsat is the bulk unit weight when every void is full of water.
- Submerged (buoyant) unit weight γ′ = γsat − γw applies below the water table, where water pushes up on the grains.
The unit weight of water γw is 9.81 kN/m³, and many exam papers allow 10 kN/m³ for quick working. Typical soils have a dry unit weight of about 14 to 18 kN/m³ and a saturated unit weight of about 18 to 21 kN/m³. A submerged soil weighs only about half as much, roughly 8 to 11 kN/m³.
Why it matters. Dry unit weight is the field engineer's daily number: every embankment specification asks for a minimum dry density. Submerged unit weight explains why the same soil gives very different earth pressure and bearing capacity once the water table rises after the monsoon.
Deriving every relation from one block
Students often try to memorise twenty formulas. A better way is to remember one trick: take the volume of solids as 1. Then every other quantity follows from the definitions.
If Vs = 1, then Vv = e and the total volume is 1 + e. The volume of water is Vw = S·Vv = Se. The mass of solids is G·ρw, because the solids occupy unit volume and are G times as dense as water. The mass of water is Se·ρw.
Now the main relations fall out one by one:
- Water content is w = Mw/Ms = Se·ρw/(G·ρw), which gives the most used relation of all: Se = wG.
- Dry unit weight is the weight of solids over the total volume: γd = Gγw/(1 + e).
- Bulk unit weight adds the water: γ = (G + Se)γw/(1 + e).
- When S = 1, the bulk unit weight becomes γsat = (G + e)γw/(1 + e).
- Subtracting γw gives γ′ = (G − 1)γw/(1 + e).
- Since γ includes water and γd does not, γd = γ/(1 + w).
One more relation is useful for compaction. With percentage air voids na, the dry unit weight is γd = (1 − na)Gγw/(1 + wG). Putting na = 0 gives the zero-air-voids line γd = Gγw/(1 + wG), which is the highest dry unit weight possible at a given water content.
Why it matters. Exams give three known values and ask for a fourth, and the block method always works without memorising. In the field, the same relations let a site engineer turn a quick moisture reading and a bulk density into the dry density that the specification asks for.
Worked examples, step by step
Example 1. A soil has void ratio 0.72, water content 12% and G = 2.72. Find its dry unit weight, its bulk unit weight and the water to be added per m³ to saturate it. Take γw = 9.81 kN/m³.
- The dry unit weight is γd = Gγw/(1 + e) = 2.72 × 9.81 / 1.72 = 15.51 kN/m³.
- The bulk unit weight is γ = γd(1 + w) = 15.51 × 1.12 = 17.38 kN/m³.
- The present degree of saturation is S = wG/e = 0.12 × 2.72 / 0.72 = 0.453, so the soil is about 45% saturated.
- Per unit volume of solids, the voids are 0.72 and the water already present is wG = 0.326, so the empty voids are 0.394. Dividing by the total volume 1.72 gives 0.229 m³ of empty voids in every m³ of soil.
- So about 229 litres (229 kg, a weight of about 2.25 kN) of water must be added to each cubic metre.
Example 2. A field sample has a bulk unit weight of 19.0 kN/m³ and a water content of 15%, with G = 2.70. Find e, n and S.
- The dry unit weight is γd = 19.0 / 1.15 = 16.52 kN/m³.
- From γd = Gγw/(1 + e), we get 1 + e = 2.70 × 9.81 / 16.52 = 1.603, so e = 0.603.
- The porosity is n = e/(1 + e) = 0.603 / 1.603 = 0.376, which is about 37.6%.
- The degree of saturation is S = wG/e = 0.15 × 2.70 / 0.603 = 0.67, which is about 67%.
Why it matters. Example 1 is exactly the calculation a site engineer makes when deciding how much water a tanker must spray on a layer before rolling. Example 2 is how a field density test result is turned into void ratio and saturation for a settlement check.
Relative density: how tightly a sand is packed
For clays, water content tells most of the story. For sands and gravels, what matters most is how tightly the grains are packed, and void ratio alone cannot tell us that. A void ratio of 0.6 may be loose for one sand and dense for another, because each sand has its own loosest and densest state.
So we compare the present state with the two limits. The loosest state has the maximum void ratio emax, and the densest has the minimum void ratio emin. The relative density (also called density index) is:
ID = (emax − e) / (emax − emin) × 100%
A sand at emax has ID = 0%, and one at emin has ID = 100%. The usual description bands are:
| Relative density (%) | Description |
|---|---|
| Below 15 | Very loose |
| 15 to 35 | Loose |
| 35 to 65 | Medium |
| 65 to 85 | Dense |
| Above 85 | Very dense |
For example, a sand with emax = 0.90, emin = 0.45 and e = 0.60 has ID = 0.30/0.45 = 67%, so it is dense. Relative density can also be written with dry unit weights, but dry density cannot be found from relative density alone, because emax and emin depend on the grading and angularity of each sand.
Why it matters. Loose saturated sand can lose almost all its strength during an earthquake, which is called liquefaction. Dense sand gives high bearing capacity and little settlement. That is why fill behind bridge abutments and under machine foundations is usually specified as a minimum relative density.
Measuring the numbers in the lab and on site
Three measurements feed every phase calculation: water content, specific gravity and bulk density. Once you have them, the block method gives everything else.
Water content is the simplest test. A small sample of 15 to 30 g of moist soil goes into a weighed can with a lid. It is dried overnight in an oven kept at 110 ± 5 °C and weighed again.
The loss in mass is the water, and dividing by the dry mass gives w. At least three samples are tested and averaged.
On site, engineers cannot wait overnight. A rapid moisture meter mixes the wet soil with calcium carbide in a sealed flask. The gas produced builds a pressure that a dial converts to water content within minutes, and the reading is then corrected to the oven-dry value.
Specific gravity of grains finer than 2 mm is found with a 50 ml density bottle, also called a pycnometer. About 10 g of dry soil is weighed in the bottle, covered with de-aired water, and the trapped air is removed by vacuum. Comparing the weights of bottle plus soil plus water and bottle plus water alone gives the volume of the grains, and so G.
Field density tells you how much soil is packed into each cubic metre in place. In the sand replacement method, a hole is dug, the soil from it is weighed, and the hole's volume is found by filling it with dry sand of known density from a calibrated cylinder. The core cutter method drives a steel cylinder of known volume into soft, fine-grained soil. Either way, the bulk density and a moisture reading give the field dry density.
Try it yourself. On ujjwalinfra, the three-phase diagram tool takes any three known values and redraws the block with every other quantity and its working. The guided sand replacement lab and the compaction lab with a rapid moisture meter walk through these site tests step by step and give a data sheet at the end.
Why it matters. Every highway, canal bank and railway formation is accepted or rejected on field dry density tests. A JE on site runs these tests daily, and an AE signs off the results, so both must understand exactly what each number means.
Quick revision
- Soil is a three-phase system of solids, water and air, and a dry or saturated soil has only two phases.
- Physical weathering gives coarse soils without changing minerals, while chemical weathering gives fine soils with new minerals.
- Residual soils stay in place, and transported soils are alluvial, lacustrine, marine, glacial or aeolian.
- Void ratio is e = Vv/Vs, porosity is n = Vv/V, and they are linked by n = e/(1 + e).
- Water content is w = Mw/Ms, it is based on the dry mass, and it can exceed 100%.
- The key relation Se = wG links saturation, void ratio, water content and specific gravity.
- Dry unit weight is γd = Gγw/(1 + e) = γ/(1 + w), and it is the number used to control compaction.
- The submerged unit weight is γ′ = (G − 1)γw/(1 + e), and it is used below the water table.
- Relative density ID = (emax − e)/(emax − emin) describes sands, from very loose below 15% to very dense above 85%.
- Water content is measured by oven drying at 110 ± 5 °C, G by a density bottle, and field density by sand replacement or core cutter.